Skyjacker MS968 Manuel d'utilisateur télécharger pdf

2001-03 2500 HD

2002-03 Hummer

Multiple Shock Instructions

Part# MS968 / MS268

MS2968-UD1 UPPER HOOP,DRIVER 1

MS2968-UP2 UPPER HOOP,PASSENGER 1

MS2968-UBB3 UPPER BOTTOM BRACKET 2

MS2968-LBB4 LOWER BOTTOM BRACKET 2

MS2968-BR BRAKE LINE BRACKET 2

38X1TCFB 3/8 X 1 THRD-CUTTER FLG BOLT 12

12X4FTB 1/2 X 4 FINE THREAD BOLT 4

12X3FTB 1/2 X 3 FINE THREAD BOLT 8

38SAEW 3/8 SAE WASHER 12

14SAEW 1/4 SAE WASHER 4

38X234FTB 3/8 X 2 3/4 FINE THREAD BOLT 4

38X1FTB 3/8 X 1 FINE THREAD BOLT 2

6X30MMBG5 6MM X 30 METRIC BOLT/ 8.8 4

516X1FTB 5/16 X 1 FINE THRD BOLT 2

12FTN 1/2-20 FINE N/I LOCK NUT 12

38FTN 3/8-24 FINE N/I LOCK NUT 6

516FTN 51/6-24 FINE N/I LOCK NUT 2

12SAEW 1/2 SAE WASHER 24

516SAEW 5/16 SAE WASHER 4

1. Park the vehicle on flat level ground. Set the emergency brake

and properly block the tires.

2. Raise the front of the vehicle and support the frame rails using

jack stands. Remove the front tires.

3. Remove the bushing and washer from the upper portion of the

factory shock. Place the new upper frame bracket over the fac-

tory bracket. (See Photo #1). Now reinstall the upper bushing

and washer onto the factory shock.

4. Push the bracket up flush against the frame. The outside

mounting hole on the top plate will now line up with the factory

hole in the upper mount. Drill out the factory hole using a

13/32” drill bit. Install the 3/8 x 1 fine thread bolt with washers

and locknut at this location. (See Photo #2).

5. Mark one of the outer holes on the front and rear of the brack-

et where it mounts to the frame. (Some models will line up with

1 factory hole in the frame). It is recommended to drill and

install the front bolt first then move to the rear mount. Drill

using a 5/16” drill bit. Once drilled, install the 3/8 x 1” thread

cutter bolt. Once 1 bolt has been installed on the front and

rear, drill the remaining outer holes and install the 3/8” bolts.

6. With all of the outer bolts installed. Mark and drill the center

hole using a 1/2” drill bit. Be sure not to drill into any power

steering lines or wiring. It will be necessary on some models to

remove the factory exhaust heat shield from the backside of

the frame to allow for installation. Once installed, reinstall the

heat shield. Once drilled, install the 1/2 x 4” fine thread bolts

with washers and nuts. Be sure to install the bolt from inside

pointing out. (See Photo #4). The new brakeline bracket will

attach under the bottom bolt in the front mount. Attach the fac-

tory brakeline bracket to the extension bracket using the 5/16 x

1” fine thread bolt, washers, and locknut. (See Photo #4).

Photo #1

Photo #2

Photo #3

Photo #4

I-MS268/MS968 12-03 Pg 1

Part # Description Qty.

1 2

Résumé du contenu

Page 1 - Part# MS968 / MS268

2001-03 2500 HD2002-03 HummerMultiple Shock InstructionsPart# MS968 / MS268MS2968-UD1 UPPER HOOP,DRIVER 1MS2968-UP2

Page 2

7. Install the new lower bracket on top of the factory upper A-Arm. The two outside bolts will line up with factory holes inthe upper A-Arm. Attach th

Modèles reliés MS268

Commentaires sur ces manuels

Pas de commentaire

Skyjacker MS968 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Skyjacker MS968. Skyjacker MS968 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés MS268

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Skyjacker MS968