Skyjacker SKTOY30 Manuel d'utilisateur télécharger pdf

IMPORTANT NOTES

-Skyjacker strongly advises taking extreme caution when working with loaded coil springs to

prevent accident or harm.

-On trucks without manual locking hubs, ride height must not be adjusted over 2" above fac-

tory ride height.

-Both coil over assemblies should be adjusted to the same length after installation. It is VERY

IMPORTANT that after installation the coil does not have any slack between the mounting

cups. At no time during axle travel should the coil lose contact with the mounting points.

-When final adjustments are made the upper spanner must be tightened. At no time should

the coil over assembly be ran without the spanner being tight.

Part # Description Qty

TOY20153-S TOYOTA 3” COIL 2

SKY202-S 2”COIL OVER SHOCK 2

SKSPC-TOYLWLG SHOCK SPACERS-LONG LOWER 2

SKSPC-TOYLWSH SHOCK SPACERS-SHORT LOWER 2

SPC-50X375 SPACER,1/2”ID X .375 LONG 4

SKY-SEAT20 SPRING SEAT:FOR SKY202-S 2

TTCSKUP-RING TOYOTA COIL OVER UPPER RING 2

12X4SHB 1/2 X 4 SOCKET HEAD BOLT 2

38X1FTB 3/8 X 1 FINE THREAD BOLT 6

12CTN 1/2-13 COARSE N/I LOCK NUT 2

38FTN 3/8-24 FINE N/I LOCK NUT 6

SW201 SPANNER WRENCH 1

Instructions:

* PreAssemble Coil Overs per instructions on page #4.

Front:

1. With vehicle on flat level ground, measure from center of

front spindle to the top of fender opening. Record this

measurement for later use.

2. Raise the front of vehicle in the center of the front cross

member using floor jack.

3. Support the vehicle on the frame cross member so that the

front tire/wheels are off the ground.

4. Using 19mm wrench remove bottom bolt from bottom of

factory shock. Bolt will be reused to install new Platinum

Series assembly.

5. Using 14mm wrench remove top three retaining nuts from

top of factory coil over assembly. Remove factory coil over

assembly. ( See Photo #1).

6. Attach upper bracket to the top of the new shock using ½"

Allen head bolt and self-locking nut as shown in Photo #2.

Be sure to use the 1/2" x .375" long spacer on each side

of the shock eye.

Photo #1

Pg 1

96-04 Toyota Tacoma

99-04 Toyota Tundra

2-2.5" Platinum Series Coil Over

Installation Guide

Part# SKTOY30

I-SKTOY30 3-06

Photo #2

1 2 3 4

Platinum Series Coil Over 4
Assembly 4

Résumé du contenu

Page 1

IMPORTANT NOTES-Skyjacker strongly advises taking extreme caution when working with loaded coil springs to prevent accident or harm.-On trucks without

Page 2

Pg 27. Disconnect sway bar end link and upper ball joint. This will allow the steering knuckle to drop allowing for an easier installation. Attach the

Page 3

Rear:10. Raise the rear of the vehicle and remove the rear tires. Remove the rear shocks using a 17mm socket. (See Photo #8).11. Disconnect the brakel

Page 4 - Assembly

1. Photo #1 shows the shock the way the coil over will be received in the box. 2. Install lower spring seat on to shock. Using a spring compressor, in

Commentaires sur ces manuels

Pas de commentaire

Skyjacker SKTOY30 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Skyjacker SKTOY30. Skyjacker SKTOY30 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Skyjacker SKTOY30